Performance Comparison of CSC Converter based ACS
Article Sidebar
Published
Dec 30, 2021
Download
Statistic
Main Article Content
Abstract
The design, operating principle and analysis of an air condition system (ACS) using with bridge and without bridge
configurations are presented for power quality improvement. The performance of these ACSs is compared on various parameters
such as voltage regulation, input current harmonic spectrum etc to choose the optimal configuration according to user’s
specifications. Both the input converters are designed in discontinuous mode to for simple control and well as inherent power
factor correction. The observed performance of both the ACSs is well within the set guidelines of international power quality
standards.
configurations are presented for power quality improvement. The performance of these ACSs is compared on various parameters
such as voltage regulation, input current harmonic spectrum etc to choose the optimal configuration according to user’s
specifications. Both the input converters are designed in discontinuous mode to for simple control and well as inherent power
factor correction. The observed performance of both the ACSs is well within the set guidelines of international power quality
standards.
Article Details
References
[1] ] J. R. Handershot, T.J.E Miller, Design of Brushless Permanent Magnet Motors, Clarendon Press, Oxford, 2010.
[2] C. L. Xia, Permanent Magnet Brushless DC Motor Drives and Controls, Wiley Press, Beijing, 2012.
[3] ] Limits for Harmonic Current Emissions, ] Limits for Harmonic Current Emissions, International Electrotechnical Commission Standard, IEC-61000-3-2 (2004).
[4] B. Singh, V. Bist, A BL-CSC Converter Fed BLDC Motor Drive with Power Factor Correction, IEEE Transactions on Ind. Electron., vol.62, no.1, pp. 1-12 (2015).
[5] Reshma T. P., Rashmi M. R, Power Factor Correction in Brushless DC Motor Dual Drive Using Bridgeless Canonical Switching Cell Converter, 2nd International Conference on Power and Embedded Drive Control (ICPEDC), pp. 258-263 (2019).
[6] A.R.Hegde, A. K. N, T. Meenakshi , M V. Pai, Power Factor Correction of Four Switch BLDC Motor Drive Using Bridgeless-CSC Converter, IEEE International Conference on Advances in Electrical Technology for Green Energy (ICAETGT’ ), pp. 56-63 (2017).
[7] A. S. Nair, A. K. W. C., Dual Mode Control Strategy for BLDC Motor Drive with Bridgeless Canonical Switching Cell Converter, International Conference on Power Electronics, Drives and Energy Systems (PEDES), pp. 1-6 (2016).
[8] S. Narula, B. Singh, G. Bhuvaneswari, A. Chandra, K. A. Haddad, Power Quality Improved SMPS Using BL-CSC Converter for Welding Applications, 2016 IEEE Industry Applications Society Annual Meeting, pp.1-8 (2016).
[9] H. Luo, J. Xu, Y. Luo, J. Sha, A Digital Pulse Train Controlled High Power Factor DCM Boost PFC Converter Over a Universal Input Voltage Range, IEEE Trans. Ind. Electron., vol.66, no. 4, pp. 2814-2824 (2019).
[10] K. Akter, G. Sarowar, M. A. Hoque ,S.F.B. Ahmed, Modeling and Simulation of Input Switched AC-DC SEPIC Converter with PFC Control for Optimized Operation, 4th International conference on Electrical Engineering and information & Communication Technology (ICEEICT), pp. 240-245 (2018).
[11] P. J. S. Costa, C. H. I. Font,T. B. Lazzarin, A Family of Single- Phase Voltage-Doubler High-Power-Factor SEPIC Rectifiers Operating in DCM, IEEE Trans. Power Electron., vol. 32, no.6, pp.4279 – 4290 (2017).
[12] B. Singh, A. Anand, Power Factor Correction in Modified SEPIC Fed Switched Reluctance Motor Drives, IEEE Trans. Ind. Appl. vol.54, no.5, pp. 4494-4505 (2018).
[13] A. Anand, B. Singh, Modified Dual Output Cuk Converter-Fed Switched Reluctance Motor Drive With Power Factor Correction, IEEE Trans. Power Electron., vol. 34, no.1, pp. 624-635 (2019).
[14] A. Anand, B. Singh, Power Factor Correction in Cuk–SEPIC-Based Dual-Output-Converter-Fed SRM Drive, IEEE Trans. Ind. Electron., vol.65, no. 2, pp. 1117-1127 (2018).
[15] A. Jha, B. Singh, High power factor and low total harmonics distortion using critical conduction mode boost converter–fed light-emitting diode driver, Int. Trans. Elect. Energy Syst., vol.10, pp. 1–11 (2016).
[16] G .R.P.Lakshmi, Power factor improvement of Canonical switch cell Converter fed BLDC Motor Drive, 2016 International Conference on Computation of Power, Energy Information and Communication (ICCPEIC), pp. 624-627 (2016).
[17] A.T.S. Subramanian, P.Sabarish, A.N. Ali, A Power Factor Correction Based Canonical Switching Cell Converter For VSI Fed BLDC Motor By Using Voltage Follower Technique, International Conference on Electrical, Instrumentation and Communication Engineering (ICEICE), pp. 1-8 (2017).
[18] A. Jha, B. Singh, Power Quality Improvement Using CSC Converter for High Power LED Driver, IEEE 6th International Conference on Power Systems (ICPS), pp. 1-6 (2016).
[19] S.P. Litrán, E. Durán, M.B. Ferrera, J. Semião, R. S. Barroso, A Zeta-CSC Converter Combination for Single-Input and Bipolar Output, IECON 2019 - 45th Annual Conference of the IEEE Industrial Electronics Society, pp. 5721-5726 (2019).
[20] Rahul Pandey, B. Singh, A Canonical Switching Cell (CSC) Converter Based Power Factor Corrected Battery Charger for E-Rickshaw, IEEE International Conference on Power Electronics, Smart Grid and Renewable Energy (PESGRE), pp. 1-6 (2020).
[21] H. Ma, Y. Li, J. S. Lai, C. Zheng, J. Xu, An Improved Bridgeless SEPIC Converter Without Circulating Losses and Input-Voltage Sensing, IEEE Journal of Emerging and Selected Topics in Power Elecntroics, vol 6, no. 3, pp. 1447-1455 (2018).
[22] R. Kumar, S.S. Kumar, PFC Using Bridgeless SEPIC Converter, 2nd International conference on Electronics, Communication and Aerospace Technology (ICECA), pp.1620-1624 (2018).
[23] P. J. S. Costa, C. H. I. Font, T. B. Lazzarin, Single-Phase Hybrid Switched-Capacitor Voltage-Doubler SEPIC PFC Rectifiers, IEEE Trans. Power Electron., vol. 33, no. 6, pp. 5118- 5130 (2018).
[24] B. R. Ananthapadmanabha, R. Maurya, S. R. Arya, Improved Power Quality Switched Inductor Cuk Converter for Battery Charging Applications, IEEE Trans. Power Electron., vol. 33, no. 11, pp. 9412- 9423 (2018).
[25] Y. Liu, Y. Sun, M. Su, A Control Method for Bridgeless Cuk/Sepic PFC Rectifier to Achieve Power Decoupling, IEEE Trans. Ind. Electron., vol. 64, no. 9, pp. 7272-7276 (2017).
[26] X. Lin, F. Wang, New Bridgeless Buck PFC Converter with Improved Input Current and Power Factor, IEEE Trans. Ind. Electron., vol. 65, no. 10, pp. 7730-7740 (2018).
[27] A. Jha, B. Singh, Bridgeless ZETA PFC Converter for Low Voltage High Current LED Driver, 6th International Conference on Computer Applications in Electrical Engineering-Recent Advances (CERA), pp. 539-544 (2017).
[2] C. L. Xia, Permanent Magnet Brushless DC Motor Drives and Controls, Wiley Press, Beijing, 2012.
[3] ] Limits for Harmonic Current Emissions, ] Limits for Harmonic Current Emissions, International Electrotechnical Commission Standard, IEC-61000-3-2 (2004).
[4] B. Singh, V. Bist, A BL-CSC Converter Fed BLDC Motor Drive with Power Factor Correction, IEEE Transactions on Ind. Electron., vol.62, no.1, pp. 1-12 (2015).
[5] Reshma T. P., Rashmi M. R, Power Factor Correction in Brushless DC Motor Dual Drive Using Bridgeless Canonical Switching Cell Converter, 2nd International Conference on Power and Embedded Drive Control (ICPEDC), pp. 258-263 (2019).
[6] A.R.Hegde, A. K. N, T. Meenakshi , M V. Pai, Power Factor Correction of Four Switch BLDC Motor Drive Using Bridgeless-CSC Converter, IEEE International Conference on Advances in Electrical Technology for Green Energy (ICAETGT’ ), pp. 56-63 (2017).
[7] A. S. Nair, A. K. W. C., Dual Mode Control Strategy for BLDC Motor Drive with Bridgeless Canonical Switching Cell Converter, International Conference on Power Electronics, Drives and Energy Systems (PEDES), pp. 1-6 (2016).
[8] S. Narula, B. Singh, G. Bhuvaneswari, A. Chandra, K. A. Haddad, Power Quality Improved SMPS Using BL-CSC Converter for Welding Applications, 2016 IEEE Industry Applications Society Annual Meeting, pp.1-8 (2016).
[9] H. Luo, J. Xu, Y. Luo, J. Sha, A Digital Pulse Train Controlled High Power Factor DCM Boost PFC Converter Over a Universal Input Voltage Range, IEEE Trans. Ind. Electron., vol.66, no. 4, pp. 2814-2824 (2019).
[10] K. Akter, G. Sarowar, M. A. Hoque ,S.F.B. Ahmed, Modeling and Simulation of Input Switched AC-DC SEPIC Converter with PFC Control for Optimized Operation, 4th International conference on Electrical Engineering and information & Communication Technology (ICEEICT), pp. 240-245 (2018).
[11] P. J. S. Costa, C. H. I. Font,T. B. Lazzarin, A Family of Single- Phase Voltage-Doubler High-Power-Factor SEPIC Rectifiers Operating in DCM, IEEE Trans. Power Electron., vol. 32, no.6, pp.4279 – 4290 (2017).
[12] B. Singh, A. Anand, Power Factor Correction in Modified SEPIC Fed Switched Reluctance Motor Drives, IEEE Trans. Ind. Appl. vol.54, no.5, pp. 4494-4505 (2018).
[13] A. Anand, B. Singh, Modified Dual Output Cuk Converter-Fed Switched Reluctance Motor Drive With Power Factor Correction, IEEE Trans. Power Electron., vol. 34, no.1, pp. 624-635 (2019).
[14] A. Anand, B. Singh, Power Factor Correction in Cuk–SEPIC-Based Dual-Output-Converter-Fed SRM Drive, IEEE Trans. Ind. Electron., vol.65, no. 2, pp. 1117-1127 (2018).
[15] A. Jha, B. Singh, High power factor and low total harmonics distortion using critical conduction mode boost converter–fed light-emitting diode driver, Int. Trans. Elect. Energy Syst., vol.10, pp. 1–11 (2016).
[16] G .R.P.Lakshmi, Power factor improvement of Canonical switch cell Converter fed BLDC Motor Drive, 2016 International Conference on Computation of Power, Energy Information and Communication (ICCPEIC), pp. 624-627 (2016).
[17] A.T.S. Subramanian, P.Sabarish, A.N. Ali, A Power Factor Correction Based Canonical Switching Cell Converter For VSI Fed BLDC Motor By Using Voltage Follower Technique, International Conference on Electrical, Instrumentation and Communication Engineering (ICEICE), pp. 1-8 (2017).
[18] A. Jha, B. Singh, Power Quality Improvement Using CSC Converter for High Power LED Driver, IEEE 6th International Conference on Power Systems (ICPS), pp. 1-6 (2016).
[19] S.P. Litrán, E. Durán, M.B. Ferrera, J. Semião, R. S. Barroso, A Zeta-CSC Converter Combination for Single-Input and Bipolar Output, IECON 2019 - 45th Annual Conference of the IEEE Industrial Electronics Society, pp. 5721-5726 (2019).
[20] Rahul Pandey, B. Singh, A Canonical Switching Cell (CSC) Converter Based Power Factor Corrected Battery Charger for E-Rickshaw, IEEE International Conference on Power Electronics, Smart Grid and Renewable Energy (PESGRE), pp. 1-6 (2020).
[21] H. Ma, Y. Li, J. S. Lai, C. Zheng, J. Xu, An Improved Bridgeless SEPIC Converter Without Circulating Losses and Input-Voltage Sensing, IEEE Journal of Emerging and Selected Topics in Power Elecntroics, vol 6, no. 3, pp. 1447-1455 (2018).
[22] R. Kumar, S.S. Kumar, PFC Using Bridgeless SEPIC Converter, 2nd International conference on Electronics, Communication and Aerospace Technology (ICECA), pp.1620-1624 (2018).
[23] P. J. S. Costa, C. H. I. Font, T. B. Lazzarin, Single-Phase Hybrid Switched-Capacitor Voltage-Doubler SEPIC PFC Rectifiers, IEEE Trans. Power Electron., vol. 33, no. 6, pp. 5118- 5130 (2018).
[24] B. R. Ananthapadmanabha, R. Maurya, S. R. Arya, Improved Power Quality Switched Inductor Cuk Converter for Battery Charging Applications, IEEE Trans. Power Electron., vol. 33, no. 11, pp. 9412- 9423 (2018).
[25] Y. Liu, Y. Sun, M. Su, A Control Method for Bridgeless Cuk/Sepic PFC Rectifier to Achieve Power Decoupling, IEEE Trans. Ind. Electron., vol. 64, no. 9, pp. 7272-7276 (2017).
[26] X. Lin, F. Wang, New Bridgeless Buck PFC Converter with Improved Input Current and Power Factor, IEEE Trans. Ind. Electron., vol. 65, no. 10, pp. 7730-7740 (2018).
[27] A. Jha, B. Singh, Bridgeless ZETA PFC Converter for Low Voltage High Current LED Driver, 6th International Conference on Computer Applications in Electrical Engineering-Recent Advances (CERA), pp. 539-544 (2017).